Saturday, September 8, 2012

Boy is it windy out there today!

Winds were gusting to 65 km/hr this morning. I was just about to climb back up on the boat for another session of seam sanding when a gust blew this section off the roof of the shed!

That's funny 'cause I don't remember building in a skylight! ;-) This is gonna be a PITA to fix but it's gotta be done. The inner liner of Tyvek will protect the shed from rain for awhile.

When the weather lets up I'll have to get some help and get this patched up. We've tried taping rips in the shrink wrap and they don't hold. I'm going to have to put another layer on and use some battens to hold them in place.

In hind sight the shrink wrap wasn't the best choice for a shed covering. It was the cheapest option at the time and I'm paying for that now.



Saturday, September 1, 2012

I've been thinking.....

This is when Lori always says: "Uh oh!" :-)

Well I'm always thinking. I'm the idea guy! Straddling the line between genius and insanity I say!

I'm half thinking about revisiting the infusion process for some of this boat hull project. Gotta put some more thought into that. I'll eliminate a lot of issues but also adds some expense and a great potential for disaster! No risk, no reward, correct?

Anywho, this morning I tried filling the little voids left in the tape with straight epoxy. It immediately ran straight out. I think that was my problem. The epoxy just ran out leaving dry tape behind. The peelply should have helped mitigate this actually. So I decided to mix up a batch of "baby puke" (cause that's exactly what it looks like) which is epoxy thickened with micro baloons. It really does look like the stuff Daniel used to spit up all the time! :-)

This did a better job and will require just a light sanding before the next layers go over top. There are a few larger voids that'll have to be ground out and repaired.

The tape would just not lay down on some sections. I'm suspecting I got a bad roll of tape. Either got wet or contaminated somehow. Anyhow, no biggie, I ordered another roll from Noah's so we're all set now.

The keel seams are all taped now. Just a few small parts on the very back of the keel to add some extra material for piece of mind.

Once this is all setup it's back to the sander to prep the hull for fiberglass! Thank gawd it's been a long haul with a bum knee and the heat. I'm really looking forward to getting the outside done and this thing flipped!

Time to go put my thinkin' cap on and maybe a power nappy! :-)

Standby.....



Monday, August 27, 2012

Yet one more SNAFU

After yesterday's SNAFU with the epoxy I was hoping things would get better. I was wrong.

This is part of one of the seams I taped and epoxied. It's not normal to have these small voids.

Normally the weave is totally filled with epoxy. Voids can cause a problem with water getting trapped and causing blisters. It's also an issue with structure and possible de-lamination.

I contacted the designer and vendor of the tape and got their views. It may be a roll that got wet or is otherwise sub standard. The tape on the left is from the designer and the one on the right is from another distributor. I've had no problem with the tape on right.

So I'll possibly be able to fix the problem with a good belt sanding and more epoxy. I've ordered more tape from the supplier on the right.

Going to be hot again next weekend! *sigh*


Sunday, August 26, 2012

When it's too hot in the kitchen

get the hell out! How hot was it in the boat shed today? This hot!

That's about $10 worth of epoxy that kicked off within 6 minutes at about 95 degs F! Grrrrrr!

This stuff gets hot lemme tell ya! I had to rip the glove off and toss the tray outside. It was smokin'! No shit sherlock!

I started out in the shed this morning about 8:30. It was already about 80 degs F in there but with the fans going full blast it was tolerable. I wanted to get the final layers of tape on the keel.

Working alone doing this type of job sucks. I had to resort to a lil' 3M Super 77 to keep the tape from blowing around and ending up in the dirt. I know it's not ideal but it's what I had to do.

Once I got the tape all laid out it was onto the epoxy. I knew I had to work quickly and resorted to the roller instead of the chip brush. Both are messy but the roller a little bit less so. I made it from the bow back a little farther than the tape in the lower section of the pic above. That's when I ran into problems with the epoxy kicking off too quickly. I had two paint trays in rotation because a little uncured epoxy will hasten the curing process. I'd leave one to drip out while using the other. I think I'll need to pick up a couple more trays! *sigh*

Oh well, get an early start on it again tomorrow and see if I can get the rest of the taping done. Then it's onto some really big fiberglass! :-)




Saturday, August 25, 2012

It's a good thing

Walker Bay dingy's have a one way valve in their garboard drain! We forgot to put the plug in! Well, sheeesh, it was the first voyage of "Lil' Peace" and we were a little anxious to get going. Haven't been on the water at all this year!

Here's the monstrosity rigged and ready to launch!

I was a little worried the Jeep wouldn't be able to pull this monster! :-)

Underway with the Admiral looking for hazards & snags!

We're going forward dear. The deadheads and rocks are usually the other way! :-)

The Minn Kota 55 lb thrust trolling motor worked well. It pushed us along at a max speed of 3.85 kts and we averaged 3 kts. Half power we were about 2.2 - 2.3 kts.

Time to renew my fishing license methinks! :-)